What is the purpose of pool sieving?

Keeping your pool clean is essential to always have clean water, free of insects, sludge and germs. Which is also essential to avoid contamination of the site and the emergence of skin mycoses.

To do this, you must carry out some essential procedures that help maintain water balance, such as sifting the pool. Thus, you and your family can enjoy the environment more without major worries.

When some kind of dirt comes into contact with water, it usually stays suspended for some time, floating, until gravity does its work and pushes the impurities to the bottom. This goes for dust in general and also for small insects, leaves and organic matter.

The problem starts when this material starts to dissolve. After this dirt is divided into small particles, the tendency is that it is no longer possible to retain these particles with the sieve. From then on, only brushing and vacuuming can solve the situation — with the help of a lot of chlorine, of course!

In pools installed in the open, this process happens naturally all the time, every day. In fact, this is why the water must be treated frequently, even in periods of low use. And it is precisely here that pool sieving comes in as a powerful ally for those who want to keep this space clean.

After all, the sieve allows you to remove the impurities suspended on the surface before they start to dissolve, preventing the accumulation of organic matter in the water, stopping the proliferation of algae and, consequently, leaving the water crystal clear for much longer. This process even helps to prevent the water from taking on the dreaded greenish appearance!

In addition, just do the math: if sieving the pool keeps the water clean for longer, it also means a longer interval between treatment routines, including the application of chlorine, algaecide, decanter and the other products that are part of it. of the ritual. In other words, the strainer is good for the water and good for your pocketbook.

An important tip is to always sieve in the same direction for all uses. This prevents dirt from falling from the sieve back into the pool and also contributes to the longevity of this equipment, as the mesh of the net tends to become increasingly fragile as it is used.

And when sifting, it’s also important to keep surface tension in mind: if you run the mesh over the surface too hard, the dirt tends to split or even sink. So, the ideal is to do the sieving slowly and steadily, taking the equipment out of the water only when the service is completed or when the network accumulates a large volume of debris.

Keep in mind that, like all equipment that is used in the pool, the sieve comes into contact with water that has a high concentration of chlorine. If this material is used and then left to dry — to dry in the sun, for example — the net will eventually become brittle after a few uses. Ideally, it should be washed in running water after use and stored in a dry and shady place.

The ideal is to pass the sieve in the pool whenever you see some dirt on the surface, but this process may vary depending on the environment where it is installed. For example, if the pool is under a showy mango tree, even if you are cleaning it 24 hours a day, you will still not be able to remove all the leaves, flowers and fruits that fall into the water.

If you put on a thermal protective cover, you don’t need to sieve the water as often. Now, if you leave the pool open all summer, it is recommended to use the equipment between two and three times a week.

Understanding the importance of sifting the pool is essential to avoid impurities in the water, leaving it suitable for bathing. However, remember that, in addition, it is necessary to invest in other cleaning products, such as skimmer, brush and chemical treatment. From this, it is easier to leave the place clean, preventing the proliferation of bacteria and the emergence of diseases.

When choosing a screen for your pool, it is important to keep in mind what you will normally see on the surface of the water.

If your pool is the victim of very fine dirt, it is important to choose a sieve model that has smaller holes that, consequently, will deliver a greater retention capacity.

On the other hand, those sieves whose holes are a little larger are usually easier to use as they do not create resistance in the water and hardly have their mesh clogged.

Check other blogposts here

Share this content

Share on facebook
Share on twitter
Share on linkedin
Share on pinterest